25-10-2026 10:59 AM
We have registered our move which should happen on the 30th. All sorted with contract etc. At the new house we noticed the power cable to the Open Reach equipment was taken by previous owner. I reported this and asked for a new cable to be sent, which I was told and engineer was needed, but can't be booked for day of transfer. Due to unknown timings of the switch, which I understand. I said can it be booked for the 31st then, I was told no. After swap we send a link for a call back to arrange an engineer. Which obviously by then the engineers will all be booked out on jobs. Which there qas no answer, apart from use the call back link. Unfortunately I was talking to a brick wall about arranging the engineer. Also Can my severe deafness be used as a priority call?
25-10-2026 11:54 AM
@Ciborg23 If you want to get one while you have to wait then the link below will work, you do have to wait until the EE activation date, then deal with any OR delays, it's the way unfortunately.
25-10-2026 12:31 PM
Ok thanks Jim. Have ordered one and plug in when it arrives. Hopefully it might speed things up on activation day. I'll probably ring them for an update in the week.
25-10-2026 02:26 PM - edited 25-10-2026 02:29 PM
@Ciborg23 Just do not understand why people take the PSU with them, it may also delay your activation when OR transfer's the connection across for you and finds the ONT not operational, i know my sister got a 14day delay for such a reason when connecting up to EE first time. You can only get the PSU that you purchased asap on the ONT and see what happens, hopefully everything goes smooth.👍
25-10-2026 02:44 PM
There's a sticker on it that says do not remove. Luckily we are decorating the property before, and moving in bit by bit. When I saw the box without a power cable I thought **bleep**, as we have the same system in our primary house. The power cable is being delivered tomorrow so hopefully once plugged in will see some lights, and no smoke 😂 then positive things Friday and Saturday.......maybe.....
25-10-2026 02:54 PM
@Ciborg23 Did think about wonder if there is one you have, but doing so stops that working, not sure when OR does the check to see if ONT is up and awake but get it plugged in asap, there should be no smoke, 12Vd.c operation and all centre positive on the plug connection.
01-11-2026 07:03 PM
You were right about the delays. The change over never happened Friday, even after a confirmation phonecall Thursday. We waited until Saturday AM to check, and the Router light still orange. Thankfully we had a call back link from an earlier enquiry so we filled it in at 0730 for an 0800/15 call back. Bang on 0815 they rang. Yep there's an issue. Was passed onto the internal IT bods to work on the problem. In the meantime, they're sending out a Myfi thing, if it works, we are in a poor reception area lol. But EE is the better network here. Just sit and wait, they hope to resolve the issue by end of the week. Which week I wonder lol.
01-11-2026 07:22 PM - edited 01-11-2026 07:31 PM
@Ciborg23 What is the ONT like for lights with your system, Power and Pon solid Green is good, and the Lan flicker's but little hard to see that as the EE Hub tries to get the wan connection on the system. Can be either with the problem OR not switched the info over correctly or EE not assigning there end. Good 4G mobile signal required to get the mobile unit going, but at least they have done that for you. EE at your old home so take it they said use your existing hub that was all working?
01-11-2026 08:11 PM
This is the little fella. Not even sure if its the right one for the router. It looks totally different to the one we have at the old house. We've got a Hub 7 thingy, which was working perfect.
Everything
01-11-2026 08:27 PM - edited 01-11-2026 08:59 PM
@Ciborg23 Will take a look when your posted picture get's approved for general viewing, at least good to know the EE Hub you have was taken and working before the change. Link below is kind off the three favourite's that OR likes.
Solved: Re: Smart hub 7 pro delivery. - The EE Community
You have the new Zyxel one good to the 1.6Gb/s package speed with a 2.5Gb/s Ethernet interface on it, but question why is the LAN not lit, should be solid green connected to start with and flashing with data, check the cable is plugged in good.
WAN connection of whatever 7 version you have off the EE Hub, and to that Lan for the ONT, not seen a Zyxel up close, but assuming it's like the rest for the light, solid shows you have a sync connection at 2.5Gb/s but you would have to look on the web manager to the hub to see that status.